Aeration System Parts

Questions?

Call us at (888) 382-3814

For complete aeration systems, deluxe vertical tank mount, double aeration kit, and other aeration supplies, please see our main Aermax systems page.

Note: These pumps are not designed to inject fluids. Ozone can be used under certain conditions, but wet ozone will erode the aluminum pump body. Use with ozone will void the warranty.

This page features parts for high capacity, full-vent aeration systems. Parts on this page are compatible with the Aermax systems we sell, and will interchange with parts from many water aeration systems.

We don't list venturi valves (“micronizers”), passive air vents, small aeration tanks or other parts used with low-cost aeration systems, but we can usually provide them if you call.

General Pump Information

• Weight: Around 8 lbs.

• Water resistant (can be operated in a somewhat moist room atmosphere, but should not be used outdoors).

• Withstand temperatures of 40 to 100 degrees Fahrenheit if there is not excessive moisture.

• Noise Level: Approximately 50 decibels.

• Life Expectancy: 20,000 to 25,000 hours before bearings need replacement.

• Materials: Body and most parts are aluminum. Valves are stainless steel, and the compression cup is Teflon. Pumps have 16-gauge wire.

• Compression Technology Used: Rocking Piston with Induction (not commutator) motor.

• Injection Output: 0.38 cfm @ 0 psi. 0.15 cfm @ 50 psi.

• Maximum Pressure Output: 100 psi, but recommended maximum operating pressure is 70 psi.

• Normal Air Pump Cycle: 5 to 10 psi of well pump setting. For example, if the well pump is set at 30-50 psi, the air pump might run at 30-35 psi.

• Recommended Maintenance: Replace Teflon compression cup every 12,000 hours. Replace bearings every 20,000 to 25,000 hours. The motor is self-lubricating. Do not oil.

Air Pumps

In general, the standard air pump handles treatment systems with service flow rates up to 15 gpm. All pumps include an air intake filter.

Air Pump Installation Kits

Includes pressure gauge, poly connectors, tubing, air regulator valve, check valve, and shelf.

Aeration Tanks

Air Pump Miscellaneous Kits & Parts

Maxi-Vent Kit, 115 volt

Maxi-Vent is a solenoid valve setup that releases water and excess air/gas while the air pump is introducing air to the treatment tank. Kit includes electronic solenoid valve, 3/8" brass ball valve, 3/8" tube and 3/8" mip connector, 3/8" drain and 1/2" drain connector and drain tee.

$138.00

Part # am016

Maxi-Vent Kit, 220 volt

Maxi-Vent is a solenoid valve setup that releases water and excess air/gas while the air pump is introducing air to the treatment tank. Kit includes electronic solenoid valve, 3/8" brass ball valve, 3/8" tube and 3/8" mip connector, 3/8" drain and 1/2" drain connector and drain tee.

$159.00

Part # am003

Aer-Max Vent Head Kit

1" PVC Head, diffuser, and vent distributor tube for Aer-Max Aeration units. Kit does not include riser tube for tank.

$129.00

Part # am008

Solenoid Valve for 115 volt Aer-Max Unit

Standard solenoid for 115v Aer-Max system. Solenoid only. Note: this part is also included in the 115 volt Maxi-Vent Kit.

$129.00

Part # am026

Solenoid Valve for 220 volt Aer-Max Unit

Standard solenoid for 220v Aer-Max system. Solenoid only. Note: this part is also included in the 220 volt Maxi-Vent Kit.

$139.00

Part # am027

Repair Kit for 115 and 230 volt Aer-Max Air Pumps

Repair kit for Aer-Max air pumps, containing head gasket, valve plate assembly, o-ring, cup, and felt liners.

$169.00

Part # am019

Aer-Max Systems

Systems sold on this page are designed to follow Aer-Max closed tank aeration systems. Follow the link for more information about Aer-Max systems.

Filters to Follow Aer-Max Systems

There are many options for filters that can follow an aeration system. Follow the link for some advice on treatment and some suggested filter options.